|
KB: Getting started with The RSL15 video series
[RSL15 - Knowledge Base]
Introduction
We have created a couple of short video tutorials to help you get started with the RSL15 Bluetooth® 5.2 Secure Wireless microcontroller. In these videos we demonstrate just how q…
|
|
2
|
532
|
September 15, 2022
|
|
KB: RSL10 Power Consumption Evaluation Guide
[RSL10 - Knowledge Base]
Table of Contents
Power Profiler
Measurement Equipment Setup
Hardware Setup
Software Setup
Connectable/Non-Connectable Advertising
Advertising Interval
Connection Interval
Tx Payload
Tx Pow…
|
|
17
|
3903
|
November 10, 2022
|
|
KB: RSL15 Power Consumption Evaluation Guide
[RSL15 - Knowledge Base]
Table of Contents
Power Profiler
Measurement Equipment Setup
Hardware Setup
Software Setup
Evaluating Current Measurements
Power Profiler
The spreadsheet tool included in the topic link…
|
|
2
|
1148
|
May 19, 2022
|
|
KB: RSL15 Power Consumption and Battery Estimator
[RSL15 - Knowledge Base]
Introduction
The purpose of this spreadsheet and the corresponding VBA user-forms is to generate power and current consumption estimates when the RSL15 is operating in a variety of commonly u…
|
|
3
|
1091
|
May 19, 2022
|
|
KB: Getting Started with RSL15
RSL15 is an ultra−low power secure Arm® Cortex®−M33 processor−based Bluetooth Low Energy 5.2 wireless MCU. But what can it do? Thats entirely up to you and heres how you get started!
Step 1 - Request an RSL15 evaluati…
|
|
2
|
1823
|
November 22, 2021
|
|
KB: RSL10 Power Consumption and Battery Estimator
[RSL10 - Knowledge Base]
Introduction
The purpose of this spreadsheet and the corresponding VBA user-forms is to generate power and current consumption estimates when the RSL10 is operating in a variety of commonly u…
|
|
2
|
3333
|
March 12, 2021
|
|
KB: Getting set up with the RSL10 SDK & Eclipse IDE
Question
What steps are necessary to access the RSL10 SDK and set up the Eclipse based tools
Recommendation
Go to the RSL10 product page page
Use the download buttons on the main page
Download and read the R…
|
|
25
|
7065
|
November 22, 2022
|
|
About the Bluetooth Low Energy category
|
|
0
|
2426
|
June 8, 2020
|
|
Generation of RTE_Components.h
|
|
3
|
55
|
November 25, 2022
|
|
RTC interrupt doesn't happen
|
|
6
|
107
|
November 25, 2022
|
|
Config and use of GPIOs
|
|
1
|
86
|
November 22, 2022
|
|
Using the RSL10-USB001GEVK USB Dongle as a sniffer
|
|
2
|
81
|
November 21, 2022
|
|
RSSI drop when connected
|
|
2
|
205
|
November 9, 2022
|
|
The ability to process button clicks in the remote_tx_raw example
|
|
3
|
435
|
November 18, 2022
|
|
The application shall ... when GATTC_SVC_CHANGED_CFG_IND
|
|
5
|
128
|
November 17, 2022
|
|
RSL10 LPDSP32 AudioCodecs Example Test
|
|
3
|
144
|
November 17, 2022
|
|
Data order when transmitting high speed SW I2C data through BLE
|
|
5
|
127
|
November 17, 2022
|
|
Linux: unpacking ONSemiconductor.RSL10.3.7.606.pack SDK without Eclips/Keil/IAR IDE
|
|
1
|
136
|
November 15, 2022
|
|
I just purchased an EVBUM2529/D, it's missing U2 part? Is that normal?
|
|
3
|
91
|
November 11, 2022
|
|
Erase method in RSL Deep Sleep Mode
|
|
1
|
74
|
November 11, 2022
|
|
How to calculate ADC delay time?
|
|
2
|
209
|
November 10, 2022
|
|
NVIC_SystemReset() vs Sys_BootROM_Reset()
|
|
3
|
129
|
November 9, 2022
|
|
How to keep a variable while sleeping
|
|
3
|
128
|
November 9, 2022
|
|
High current(176mA) when rsl is wakeup
|
|
1
|
126
|
November 7, 2022
|
|
Are there any decent sources of documentation/sample projects/code for the Ultra Low Power Data Aquisition System for the RSL15?
|
|
2
|
139
|
November 7, 2022
|
|
Getting a current of 14mA during advertisement
|
|
1
|
117
|
November 7, 2022
|
|
RSL10 Rebooting if disconnected from debug link
|
|
4
|
247
|
November 7, 2022
|
|
Quuppa emultation
|
|
9
|
435
|
November 7, 2022
|
|
Which timer usage is better for periodic work?
|
|
1
|
149
|
November 4, 2022
|
|
How to handle GAPC_LE_PHY_IND, GAPC_LE_PKT_SIZE_IND and GAPC_GET_DEV_INFO_REQ_IND events
|
|
6
|
253
|
November 2, 2022
|
